Arrow ELPHD64 Gebrauchs- und Pflegehandbuch

Gloves must be worn at all times to reduce risk of injury!Owner’s Manual& Assembly Guide01AB719380814Model No. ELPHD64Nominal Size6’ x 4’www

ASSEMBLY BY KEY NO.1010ABRoof3333353535353434373636363636363636Doors2115262226322229191619172027293230232428253125241818

11ASSEMBLY OVERVIEWBuild the Floor FrameInstall Corner Panels, Side Angles, Rear Angles, and Door JambsInstall Wall Panels and Wall ChannelsAttach Hea

12CONSTRUCTING A BASE...FRONT(DOOR)FRONT(DOOR)Note: Finished Slab dimensions, with lumber removed.No matter which of the options below you choose for

6Step 1: Front Corners and Door Jamb1313ABYou will need for this page:108392Front Corner Panel1083980057/1071610716Right Door Jamb180057Left Door Jamb

6Step 2: Door Pre-Assembly1414ABYou will need for this page:10718Horizontal Door Brace4107192Door Handle Brace10856Door Panel210718107191071810856(QTY

6Step 3: Right Door Assembly1515ABYou will need for this page:(QTY: 6)FB66609Hinge266054Latch166809Locking Handle Right1(QTY: 2)LNB666096680966054LNBF

6Step 4: Left Door Assembly1616ABYou will need for this page:(QTY: 6)FB66609Hinge2(QTY: 2)LNB66810Left Handle166609FB66810LNB12Install Locking Handle

6Step 4: ContinuedRemove far left Screw from top and bottom Horizontal Door Brace to install Door Stop and Latch Springs.1717ABYou will need for this

6Step 5: Floor Assembly1818AB(QTY: 8)SSFront10849210850210850108501084910849Assemble the four (4) corners of the Floor Frame using two (2) Sand Screws

19Always attach Wall Panels to Floor Frames with Screws as shown. Rest Panel on Floor Frame, aligning holes in the Panel and Floor Frame.(QTY: 6)Use o

2SAFETY PRECAUTIONS...Safety precautions MUST be followed at all times throughout the construction of your building!Care must be taken when handling v

20You will need for this page:Step 7: Wall Framing20AB(QTY: 6)SS10851RearWall Angle110852Side Wall Angle2Wall Angles must face inside the building.

21Whenever a crimped rib and an uncrimped rib meet, the crimped rib should be placed UNDER the uncrimped rib if possible.Wall Panel26155Wall Panel1107

22(QTY: 10)(QTY: 72)Attach Wall Panels with screws through all holes in top and bottom of Panels.You will need for this page:Step 8: ContinuedWorking

23You will need for this page:Insert screw where Channels meet.Step 9: Wall ChannelsInstall Rear Wall Channel by placing Sand Screws through all rem

24Edge Trim (Plastic)Left Gable17907Edge Trim MUST cover Gable edge.(QTY: 4)Leg of Gable Brace must face toward large end of Gable as shown.You will n

25You will need for this page:Step 10: Continued25AB(QTY: 12)SSWorking one (1) Gable at a time, attach Gables to Side Wall Angles with six (6) Sand

26You will need for this page:Step 11: Roof FramingAttach Roof Beam to Gable Brace using two (2) Sand Bolts and Nuts per end as shown.126ABAttach Roof

27You will need for this page:Step 12: Window AssemblyAttach Lower Window Header to the Front Header using ten (10) Sand Screws as shown. Leave holes

28SBSBSB10844 10844You will need for this page:Step 12: Continued28ABWindow Upright Inner210844Window Support Angle Lower210847Attach Window Upright I

29You will need for this page:Step 12: Continued29AB Window266830Insert Windows inside Window Header Lower. Place between Window Upright Inner and Win

3ASSEMBLY TIPS & TOOLSHow to Select and Prepare Your Building Site: Before you start to assemble your building, you will want to decide on a good

30You will need for this page:Step 12: Continued30ABAttach Window Header Upper and Window Support Angle Upper to window assembly using four (4) Long B

31Roof Install Prep Page31ABMeasure the building diagonally again to make sure the building is square. The building should be square at the base

32You will need for this page:Step 13: Roof Assembly32ABWorking one (1) Panel at a time, secure Right Roof Panel to Header Assembly by placing one (1)

33You will need for this page:Step 13: Continued33ABAttach Panels #3 and #4 in order given in the diagram on page 31. Use the diagram to the right whi

34You will need for this page:Step 13: Continued34ABAttach Panel #5, use the diagram to the right while assembling the roof. 5An Awl may be used to h

35You will need for this page:Step 14: Roof Trim35ABPosition Roof Trim and secure with eight (8) Meadow Green Screws. Do not fasten the last screw on

`3636ABYou will need for this page:NEED AT LEAST TWO PEOPLE TO PERFORM THIS STEP!(QTY:12)FB10702Ramp1(QTY:4)SSStep 15: Door Installment1SSSSSS2SS10702

37ANCHORING OPTIONS...The entire fl oor frame MUST be securely anchored once the building is erected. Below are recommended ways of anchoring. Anchori

CARE & MAINTENANCE...Exterior Care:For a long lasting fi nish, clean and wax the exterior surface. We recommend washing with a mild soap solution.

39ARROW ACCESSORIES...ANCHOR KITS Model No. AK4Anchor Kit contains heavy-duty steelaugers, 60' (18 m) of steel cable and 4 cable clamps. No diggi

4FREQUENTLY ASKED QUESTIONSQ. How long will it take to assemble the building?A. Assembly time depends on a variety of factors, including roof design,

5Q. What kind of base do I use?A. You can:•Use an Arrow Base Kit •Pour a concrete slab •Build a wood deck/fl oor (use exterior-grade plywood)•Use patio

6Q. What if the rear wall angle and channels are too large to fi t inside of the rear wall panels?A. Check the dimensions of wall assemblies. Th

7HARDWARE LIST...13 1407AB111/32 Hex.Hardware Views by Key No.9121011152#2 PhillipsSB4#2 PhillipsSS7#2 PhillipsLNB8#2 PhillipsTS6#2 PhillipsFB18

6 KeyNo.PartNo.PartDescriptionQty.List1 10849 Front/Rear Floor Frame 22 10850 Side Floor Frame 23 10702 Ramp 14 10839 Front Corner Panel 25 1070

ASSEMBLY BY KEY NO.909ABWallsFloor5858611273131917244771212141410