Model No. VD86 697.68616Owner's Manual & Assembly Instructions W01705340111 Exterior Dime
It is important that the entire floor frame be anchored after the building is erected.Below are recommended ways of anchoring. Anchoring Down The Buil
11Remove from bag of screwsand save for the last step67293Weather Stripping (1)66382Lower Door Guide (4)66183Roof Trim Cap(2 right & 2 left)67468
12Parts ListW12 ctrAssembly Part Part Quantity CheckKey No. Number Description in Carton List 1 8941 Ramp 1 2 9379 Front Floor Frame 2 3 9377 Rear
13Assembly by Key No. W13 ctr
The front floor frame is made up ofthree pieces. The rear floor frame ismade up of two pieces. The holes inthese pieces will align when thepieces are
Step 2W15 ctr15● Parts Needed For ●Frame AssemblyThe main frame pieces reinforce thewalls. This piece will later be installedat the top edge of the re
16Step 3B16 ctr● Parts Needed For ●Roof Beam Assembly●●●●● 8474 Roof Beam (1)●●●●● 8476 Side Wall Angle (1)The roof beams join the two gablesand suppo
17NOTE:Door Track Splice (painted part)Step 4B17 ctr● Parts Needed For ●Door Track Assembly●●●●● 6617 Door Track Splice (1)●●●●● 9378 Door Track (2)Th
●●●●● Front Floor Assembly (1)●●●●● 8946 Side Floor Frame (2)●●●●● Rear Floor Assembly (1)● Parts Needed For ●Floor FrameStep 5B18 ctrThe floor frame
1 Position corner posts at the cor-ner of the floor frame as shown. Fas-ten the corner post to the floor framewith two screws.Support the corner post
Owner's ManualBefore beginning construction, check local building codes regarding footings, locationand other requirements. Study and understand
The door jambs reinforce the dooropening and provide an attractivetrim. The splice post supports therear wall.1 Position splice post at the centerof
The studs provide a surface for at-taching the siding panels.1 Following dimensions, measuringfrom the ends of angles, place a studbetween each corner
Each screw in the wall requires awasher.1 Slide side siding into channelsof corner posts, flat edge upward,bottom edge down resting on floorframe. A
1 Slide rear siding into channel ofcorner and splice posts fastening torear frame as shown in previous step.2 Install rear siding to completeeach se
24The gables go on top of the front andrear walls to support the roof beams.NOTEThe gables are packed nestedtogether and might be mistakenas one piece
1 Lift and fasten a right and leftgable, under angle at corner, to therear wall angle with screws.Hint: On the rear gable, use a boltand nut at the
1 Fasten the main roof beam to thegable brace of the front gable.2 Fasten the other end of the mainroof beam to the gable brace of therear gable.3 Fas
27Step 14W27 ctr● Parts Needed For ●Right Roof Panel●●●●● 8466 Right Roof Panel (1)Installing the roof panels is best donewith a step ladder. Begin i
1 Install a left roof panel at the leftrear and right front corner of the roof.Install a right roof panel at the leftfront corner of the roof.2 Cut 2
1 Install the ridge cap on the com-pleted roof section using bolts. Donot fasten the ends of the ridge capuntil instructed to do so.2 Fasten the low
Selecting and Preparing Your Site: Before assembly, you will want to decide ona location for your building. The best location is a level area with goo
30●●●●● 67725 Foam Board (2)●●●●● 10486 Right and Left Doors (2)●●●●● 10503 Horizontal Door Brace (4)●●●●● 8641 Vertical Door Brace (2)● Parts Ne
31Step 18Y31 ctr● Parts Needed For ●Door Installation & Adjustment●●●●● Right Door Assembly (1)●●●●● Left Door Assembly (1)1 From inside the build
705340111VD86 697.68616 W32SOME FACTS ABOUT RUSTRusting is a natural oxidizing process that occurswhen bare metal is exposed to moisture. Problemare
Safety precautions are important to follow throughout the construction of your building.•Care must be taken when handling variouspieces of your buildi
Finish: For long lasting finish, periodically clean and wax the exterior surface. Touch-up scratches as soon as you notice them on your unit. Immedia
ACCESSORIES... A6 WEB* Some drilling required to fit buildings without mid-wall bracing.Model No. SS404• Makes 8" to 12" (20,3-30,5 cm
THIS PAGEWA SLEFTBLANKINTENTIONALLY7
THIS PAGEWA SLEFTBLANKINTENTIONALLY8
68 3/4"174,6 cmThe Base For Your Building9FRONT(DOOR)FRONT(DOOR)Base B09 ctr16"/24"40,6 cm/61,0 cmOPTION 1: ARROW FLOOR FRAME KIT:
Kommentare zu diesen Handbüchern