Storage AreaExterior Dimensions(Lid Edge to Lid Edge)Interior Dimensions(Wall to Wall)Width Depth Height Width Depth Height10 Sq. Ft. 21 Cu. Ft. 57 3/
1010LYou will need for this page:Step 5Pre-assemble Side Panels together using two (2) U-Splices and eight (8) Push Pins. Make two (2) assemblies.1106
1111LYou will need for this page:(QTY: 6)LS(QTY: 6)SBStep 6Position each Panel Assembly as shown and secure to the Floor with one (1) Large Screw in t
1212LYou will need for this page:(QTY: 6)SBStep 7667853106913Pre-assemble the Lid Stay to the Lid Stay Brace using two (2) Small Bolts and Nuts. Make
1313LYou will need for this page:(QTY:14)SS(QTY: 4)SBStep 810693Front TopChannel110694Rear Top Channel1First install top channels starting with Front
61414LYou will need for this page:Install Lid Handle Brace to Lid Handle Panel as shown using two (2) Small Screws.1Install Locking T-Handle using two
61515L • Lid Stay/Brace Assemblies (3)You will need for this page:Step 10Install three (3) Lid Stay/Brace Assemblies into the back panels by
1616LYou will need for this page:(QTY: 2)SBStep 1110697Lid Support166796Lid Catch1For the middle Lid Support attach the Lid Catch using two (2) Small
1717LYou will need for this page:(QTY: 24)SSStep 1210697Lid Support510698Lid Panel1Start lid assembly by attaching fi ve (5) Lid Supports to the Lid Pa
1818LYou will need for this page:Step 131(QTY: 9)LS(QTY: 6)SSLSSS667843Offset Hinge3Attach the three (3) Lid Stays to the Lid using six (6) Small Scre
1919LYou will need for this page:Step 14Install Latch and Plastic Spacer to the inside of the Locking T-Handle. Secure with Push Nut found in the Lock
2BEFORE YOU BEGIN...Safety precautions MUST be followed at all times throughout the construction of your Storage Unit!•Care must be taken when handlin
CARE & MAINTENANCE...Exterior Care:For a long lasting fi nish clean and wax the exterior surface. We recommend washing with a mild soap solution.
31 65103 Hex Nut (#8-32) 302 65923 Small Bolt (#8-32 x 3/8) (10 mm) 223 65004 Small Screw (#8AB x 5/16) (8 mm) 58 4 65004-57 Small Screw (Painted) (
6PARTS LIST...4Key Part Part Qty. No. No. Description ListSelected End Views by Key No
ASSEMBLY BY KEY NO.505L1211123344566666667777899910111213131514141515151516NOTE: The U-Splice, Key No. 8 (Part No. 10690) is used at each Panel
6Step 1Slide the Front and Rear Floor Channels and Side Floor Channels onto the Floor as shown. Secure using eight (8) Long Screws where holes align.
707LYou will need for this page:Step 2Once Floor is complete, measure diagonally. When the diagonal measurements are equal, the Floor is square.1Seal
808LYou will need for this page:Step 3Pre-assemble Front Panels together using two (2) U-Splices and six (6) Push Pins leaving the top paired hole vac
909LYou will need for this page:Step 4Pre-assemble Back Panels together using two (2) U-Splices and eight (8) Push Pins.110688Wall Panel310690U-Splice
Kommentare zu diesen Handbüchern